Rudder pedal springs

Discussion for Sonex builders on specific plans page experience. These posts are limited to technical suggestions such as assembly order, challenges, or techniques related to specific plans pages.

Re: Rudder pedal springs

Postby radfordc » Wed Sep 03, 2014 4:26 pm

I don't know how old is "too old" but many of us might agree that we're closer to the end of our flying career than the beginning. Just means we have to cram all the fun we can into the time remaining.

BTW, I turned 68 last April.
radfordc
 
Posts: 573
Joined: Fri Jun 03, 2011 9:39 am

Re: Rudder pedal springs

Postby DCASonex » Thu Sep 04, 2014 5:53 pm

What is with all the young guys on this site. 70+ here and know there are some older Sonex drivers.

David A.
DCASonex
 
Posts: 935
Joined: Mon Sep 12, 2011 8:04 pm
Location: Western NY USA

Re: Rudder pedal springs

Postby Bryan Cotton » Thu Sep 04, 2014 6:37 pm

On the Cessna 120/140 association forum I had assumed it was a bunch of old guys. One time the question came up and it turns out a lot of the active folks were in their 20's. I had it all wrong.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5501
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: Rudder pedal springs

Postby maishathelion » Thu Sep 04, 2014 7:15 pm

Pardon me for protruding into this age conversation but my birthdate is June 20th nineteen thirty four.I started driving at 18 and flying at 17 as a member of the Civil Air Patrol.While i have been injured while racing[but never broken anything]i have never had a reportable highway or flying accident or incident.
Former flight engineer and drill instructor
I have had 27 surgeries including 4 joint replacements,4way heart bypass,close to death from sepsis.a broken back age 14 and much much more
like the two incurable cancers i have at the same time and was supposed to be dead in 07.
I am formerly Sonex # 544 and Onex #0040.
I am now searching for my next project which i shall have to build from this damned walker.
Tomorrow i will drive myself to the hospital for a full skeletal survey and sonogram as i did while in chemo for 2 years.
I have wrestled with giving up all kinds of activities in consideration for the safety of others and when in doubt, i give it up.
maishathelion
 
Posts: 8
Joined: Tue Mar 25, 2014 10:40 pm

Re: Rudder pedal springs

Postby MichaelFarley56 » Thu Sep 04, 2014 8:15 pm

DCASonex wrote:What is with all the young guys on this site. 70+ here and know there are some older Sonex drivers.

David A.


I get the impression there's a very large age range for Sonex people. Up at Oshkosh there were people from 20's to 80's all expressing interest in the design.
Mike Farley
Waiex #0056 - N569KM (sold)
Onex #245
MichaelFarley56
 
Posts: 1485
Joined: Thu Jun 02, 2011 11:38 pm
Location: Columbus, Ohio

Re: Rudder pedal springs

Postby eppre » Fri Sep 05, 2014 8:56 am

How many guys have left the rudder pedal springs off? I am just to the point of installing them and read that some don't bother.

Pete
eppre
 
Posts: 51
Joined: Tue Mar 25, 2014 8:16 am

Rudder pedal springs

Postby Sonex1517 » Fri Sep 05, 2014 10:12 am

Pete

I am also at that point right now, but am installing them as they are on the plans. They do not seem to do much though....

Very curious of others opinions here


Robbie Culver
Sonex 1517
Chicagoland
Tails and Wings complete - finishing fuselage.
N1517S reserved
Robbie Culver
Sonex 1517
Aero Estates (T25)
First flight 10/10/2015
375+ hours
Jabiru 3300 Gen 4
Prince P Tip
Taildragger
N1517S
User avatar
Sonex1517
 
Posts: 1670
Joined: Fri Jun 03, 2011 10:11 am
Location: T25 Aero Estates, Frankston, TX

Re: Rudder pedal springs

Postby Bryan Cotton » Fri Sep 05, 2014 1:33 pm

I plan to leave mine off. Weight is the enemy.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5501
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: Rudder pedal springs

Postby Bryan Cotton » Fri Sep 05, 2014 1:35 pm

Although the springs would give you an opportunity to tweak rudder trim without the tab- just shorten one.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5501
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: Rudder pedal springs

Postby radfordc » Fri Sep 05, 2014 4:12 pm

Sonex1517 wrote:Pete

I am also at that point right now, but am installing them as they are on the plans. They do not seem to do much though....

Very curious of others opinions here


Robbie Culver
Sonex 1517
Chicagoland
Tails and Wings complete - finishing fuselage.
N1517S reserved


The only thing they really do is keep the slack out of the rudder cables on the ground. I had a spring break about 5 years ago. I removed both springs and left it like that.
radfordc
 
Posts: 573
Joined: Fri Jun 03, 2011 9:39 am

PreviousNext

Return to Sonex Plans

Who is online

Users browsing this forum: No registered users and 28 guests