SonexBuilders.net

A Forum for Sonex Aircraft Builders and Enthusiasts

Skip to content

LogoLogoLogo
random user submitted photo

Oil pump cover seal

Discussion of the Aerovee kit engine.
Post a reply

Oil pump cover seal

Postby Bryan Cotton » Sat Jan 27, 2024 11:54 am

When I got rid of my external filter, I put in a normal oil pump and I bought a Gene Berg 239 pressure relief cover. I've had lots of leakage from the pump since. Per the manual (IIRC) I put the cover onto the pump with no gasket, though there are gaskets for it. I am going to try adding the gasket. Wondering if anybody has experience or wisdom to share regarding sealing the oil pump.

Should I eliminate this leak, I am sure there are others to protect the belly of the airplane, so no worries there.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Oil pump cover seal

Postby Bryan Cotton » Sat Jan 27, 2024 3:01 pm

I just had a discovery. My oil pump bolts were a touch long. I don't think I had good clamping on the pump and cover.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Oil pump cover seal

Postby Area 51% » Sat Jan 27, 2024 3:17 pm

Probably why the stock VW case comes with studs and nuts.
Area 51%
 
Posts: 804
Joined: Thu Feb 18, 2016 7:57 am
Top

Re: Oil pump cover seal

Postby Bryan Cotton » Sat Jan 27, 2024 3:31 pm

Area 51% wrote:Probably why the stock VW case comes with studs and nuts.

Yeah I can see that being better. I skipped the cover gasket and just used sealer. The original oil pump setup was fine. It had a thicker cover. Not sure how I missed that before.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Oil pump cover seal

Postby bvolcko38 » Mon Jan 29, 2024 10:12 am

Def need a gasket! 2 in fact! One for the pump one for the cover!
Bill Volcko XNS0068
Xenos A N68WV 99% flush rivets
Aerovee and Prince P-Tip
MGL Discovery Lite w/ Sandia STX 165R
V6
First hole 4/1/16
First flight 8/24/18
Phase I complete...finally!!!
Also flying a Challenger II since 1999
User avatar
bvolcko38
 
Posts: 284
Joined: Fri Feb 19, 2016 7:40 am
Location: Finger Lakes
Top

Re: Oil pump cover seal

Postby Bryan Cotton » Mon Jan 29, 2024 10:19 am

bvolcko38 wrote:Def need a gasket! 2 in fact! One for the pump one for the cover!

The Aerovee manual says no gasket under the cover. That worked for me before, so I'm trying it again with my shortened bolts. If it doesn't work I'll use the cover gasket.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Oil pump cover seal

Postby daleandee » Mon Jan 29, 2024 4:37 pm

Bryan Cotton wrote:
bvolcko38 wrote:Def need a gasket! 2 in fact! One for the pump one for the cover!

The Aerovee manual says no gasket under the cover. That worked for me before, so I'm trying it again with my shortened bolts. If it doesn't work I'll use the cover gasket.


Be certain the plate is flat. One trick is to use some fine emory cloth on a sheet of glass to polish the surface of the cover.

Dale
3.0 Corvair/Tailwheel
User avatar
daleandee
 
Posts: 877
Joined: Fri Feb 01, 2013 6:14 pm
Top

Post a reply

Return to Aerovee

Who is online

Users browsing this forum: No registered users and 53 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

SonexBuilders.net is NOT affiliated with Sonex Aircraft LLC. Discussion contents reflect the views of individual participants only. The owner of SonexBuilders.net makes no guarantees about the correctness or the accuracy of ANY of the information on or in any area or page of SonexBuilders.net. Verify ALL information obtained from SonexBuilders.net with the kit designer, equipment manufacturer, or other original official source before using that information. By participating in this website in any form, (including but not limited to reading, viewing, posting, and private messaging) you agree not to hold the owner (AVED LLC), owner members, forum members, or advertisers of SonexBuilders.net legally liable for information found on any of the pages of the website.

SonexBuilders.net is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.