random user submitted photo
billy's plans built sonex 1735
Re: billy's plans built sonex 1735
by Bryan Cotton » Mon Jun 24, 2019 7:59 am
I routed 1/4" poly tube through 3 of the tooling holes and ran the wires in separate tubes. Was cheap and very little work.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
-
Bryan Cotton - Posts: 5496
- Joined: Mon Jul 01, 2013 9:54 pm
- Location: C77
Re: billy's plans built sonex 1735
by DCASonex » Mon Jun 24, 2019 8:52 am
If not sure you will add lights, just run the poly tubing, and save cost and weight of wires. Just make sure tubing is large enough to add big enough multi-conductor cable to connect landing lights as wing wag, and or to synchronize strobes if you go that way later.
David A.
David A.
- DCASonex
- Posts: 935
- Joined: Mon Sep 12, 2011 8:04 pm
- Location: Western NY USA
Re: billy's plans built sonex 1735
by Rofomoto » Fri Jun 28, 2019 1:14 pm
Well 5 hours to rivet the right wing and fit wing tip. ( and about six cigarettes)
Electric riveter still on one battery.
Electric riveter still on one battery.
1735
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
- Rofomoto
- Posts: 612
- Joined: Sun Aug 06, 2017 2:51 pm
Re: billy's plans built sonex 1735
by Rofomoto » Sat Jun 29, 2019 7:22 am
1735
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
- Rofomoto
- Posts: 612
- Joined: Sun Aug 06, 2017 2:51 pm
Re: billy's plans built sonex 1735
by Rofomoto » Sat Jun 29, 2019 8:49 pm
Somewhere to put it
1735
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
- Rofomoto
- Posts: 612
- Joined: Sun Aug 06, 2017 2:51 pm
Re: billy's plans built sonex 1735
by Rofomoto » Sun Jun 30, 2019 9:24 am
1735
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
- Rofomoto
- Posts: 612
- Joined: Sun Aug 06, 2017 2:51 pm
Re: billy's plans built sonex 1735
by Rofomoto » Sun Jun 30, 2019 3:20 pm
So started round two
So I’m either blind, dumb or to tiered. What happens to #1 aft rib at rear spar?
So I’m either blind, dumb or to tiered. What happens to #1 aft rib at rear spar?
Last edited by Rofomoto on Sun Jun 30, 2019 3:37 pm, edited 1 time in total.
1735
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
- Rofomoto
- Posts: 612
- Joined: Sun Aug 06, 2017 2:51 pm
Re: billy's plans built sonex 1735
by Area 51% » Sun Jun 30, 2019 3:33 pm
Love the wing work stands. Are you down to one bathroom till the wings are complete?
- Area 51%
- Posts: 804
- Joined: Thu Feb 18, 2016 7:57 am
Re: billy's plans built sonex 1735
by Rofomoto » Sun Jun 30, 2019 3:39 pm
Area 51% wrote:Love the wing work stands. Are you down to one bathroom till the wings are complete?
Still have a little room...any ideas on that second picture? Left wing rib 1
1735
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
Longassproject
E-A-G-L-E-S Eagles (next year 16- 0)
- Rofomoto
- Posts: 612
- Joined: Sun Aug 06, 2017 2:51 pm
Re: billy's plans built sonex 1735
by Area 51% » Sun Jun 30, 2019 3:45 pm
I think the attach plate is supposed to go on the other side (aft side) of the rear spar. Detail G on page W12.
- Area 51%
- Posts: 804
- Joined: Thu Feb 18, 2016 7:57 am
Who is online
Users browsing this forum: No registered users and 5 guests
