NACA duct locations?

Discussion for Sonex builders on specific plans page experience. These posts are limited to technical suggestions such as assembly order, challenges, or techniques related to specific plans pages.

NACA duct locations?

Postby kevinh » Wed Jan 18, 2017 7:31 pm

HI ya'll,

So I have Peter's nice NACA vents. And I could swear I remember a place in the plans where Sonex shows where to cut the vent locations. Alas, I must now be blind because I can't find the right sheet. Anyone remember where it is?

Kevin
Taildragger Waiex in progress, tail done, wings done, about to mate wings to fuse,
then cowl, canopy, paint (photos): flush rivets, turbo aerovee, acro ailerons
(I built my RV7A and happily flew it for about 500 hrs)
User avatar
kevinh
 
Posts: 372
Joined: Mon Feb 23, 2015 10:46 pm
Location: San Mateo, CA

Re: NACA duct locations?

Postby rizzz » Wed Jan 18, 2017 7:59 pm

kevinh wrote:HI ya'll,

So I have Peter's nice NACA vents. And I could swear I remember a place in the plans where Sonex shows where to cut the vent locations. Alas, I must now be blind because I can't find the right sheet. Anyone remember where it is?

Kevin


Hi Kevin,
What plans number do you have?
This is only a guess but I have a suspicion Sonex might have removed the original vents from the plans as nearly everyone now implements their own preferred solution for this.
Most use the standard VANS vents which are placed forward of the original location, others use the half turn bowls that go in the windshield (I think Sonex themselves do that one), some use the new RV12 vents, many now go for Peter Anson's super cool solution or similar...
Anyway, if I don't forget I'll see if I can find the original location in my old plans (145) when I get home tonight.
Michael
Sonex #145 from scratch (mostly)
Taildragger, 2.4L VW engine, AeroInjector, Prince 54x48 P-Tip
VH-MND, CofA issued 2nd of November 2015
First flight 7th of November 2015
Phase I Completed, 11th of February 2016
http://www.mykitlog.com/rizzz/
rizzz
 
Posts: 869
Joined: Tue Jun 21, 2011 2:07 am
Location: Wollongong, NSW, Australia

Re: NACA duct locations?

Postby tonyr » Wed Jan 18, 2017 10:14 pm

Kevin,

No dimensions as such, but as high and as far forward as you can get them without interfering with any surrounding angles, tank etc.

(In the section just behind the vertical channel that supports the rudder block brackets)

Cheers
Tony
Sonex #813
First Flight... 4 Oct 14
298 hours having fun!
http://sonexaus.wikispaces.com/Tony+%28Richo%29+Richardson+Sonex+813
User avatar
tonyr
 
Posts: 200
Joined: Thu Jun 27, 2013 12:50 am

Re: NACA duct locations?

Postby rizzz » Wed Jan 18, 2017 10:23 pm

tonyr wrote:Kevin,

No dimensions as such, but as high and as far forward as you can get them without interfering with any surrounding angles, tank etc.

(In the section just behind the vertical channel that supports the rudder block brackets)

Cheers
Tony


You're talking about the VANS ducted naca vents right? those indeed go as far forward as possible
The standard Sonex vents were located further aft, this is also the location Peter (Anson's) vents are located.
Michael
Sonex #145 from scratch (mostly)
Taildragger, 2.4L VW engine, AeroInjector, Prince 54x48 P-Tip
VH-MND, CofA issued 2nd of November 2015
First flight 7th of November 2015
Phase I Completed, 11th of February 2016
http://www.mykitlog.com/rizzz/
rizzz
 
Posts: 869
Joined: Tue Jun 21, 2011 2:07 am
Location: Wollongong, NSW, Australia

Re: NACA duct locations?

Postby Sonex1243 » Wed Jan 18, 2017 10:30 pm

Hi Kevin;
Plans sheet SNX-F13 shows the cutout detail for mine. Not sure if it would be the same sheet for your WX though.
Ken S
SONEX #1243 N424SX (reserved)
Tail complete, wings done
Fuselage on gear
Jab 3300 received!
Sonex1243
 
Posts: 312
Joined: Thu Jan 08, 2015 4:59 pm

Re: NACA duct locations?

Postby rizzz » Wed Jan 18, 2017 10:40 pm

Sonex1243 wrote:Hi Kevin;
Plans sheet SNX-F13 shows the cutout detail for mine. Not sure if it would be the same sheet for your WX though.


Correct, I found a scan of that drawing on my PC, I almost posted it here but then remembered that might get me in trouble.
Kevin, Send me a PM if you find your plans do not detail the location of the vents.
Michael
Sonex #145 from scratch (mostly)
Taildragger, 2.4L VW engine, AeroInjector, Prince 54x48 P-Tip
VH-MND, CofA issued 2nd of November 2015
First flight 7th of November 2015
Phase I Completed, 11th of February 2016
http://www.mykitlog.com/rizzz/
rizzz
 
Posts: 869
Joined: Tue Jun 21, 2011 2:07 am
Location: Wollongong, NSW, Australia

Re: NACA duct locations?

Postby Corby202 » Thu Jan 19, 2017 2:54 am

Kevin I would suggest the main consideration for the NACA duct vent positioning would be the clearance to the brake/flap handles, so the higher the better.

Phil
Phil Bird
Sonex 759 JAB 2.2 Tailwheel
Mittagong NSW Australia
http://www.mykitlog.com/corby202/
https://www.flickr.com/photos/78427482@ ... otostream/
Corby202
 
Posts: 223
Joined: Mon Dec 30, 2013 2:08 am

Re: NACA duct locations?

Postby Corby202 » Thu Jan 19, 2017 2:54 am

Kevin I would suggest the main consideration for the NACA duct vent positioning would be the clearance to the brake/flap handles, so the higher the better.

Phil
Phil Bird
Sonex 759 JAB 2.2 Tailwheel
Mittagong NSW Australia
http://www.mykitlog.com/corby202/
https://www.flickr.com/photos/78427482@ ... otostream/
Corby202
 
Posts: 223
Joined: Mon Dec 30, 2013 2:08 am


Return to Sonex Plans

Who is online

Users browsing this forum: No registered users and 0 guests