SonexBuilders.net

A Forum for Sonex Aircraft Builders and Enthusiasts

Skip to content

LogoLogoLogo
random user submitted photo

Ream Aileron Paddle flanged pivot bearing hole?

Discussion for builders, pilots, owners, and those interested in building or owning a Onex.
Post a reply

Ream Aileron Paddle flanged pivot bearing hole?

Postby dhogue » Thu Nov 13, 2014 6:28 pm

Hello,

Is it best to use a drill press to ream pilot drilled holes?

Any suggestions where to get reasonably priced reamer bits?

I found a .6980" reamer bit at Grainger for > $90.

Thanks,
Don
Don Hogue
Onex 0173: Tailwheel: AeroVee Turbo.
Horiz/Vert Stabs, Rudder/Elevators, Fwd/IB/OB/Aileron Bellcranks on Ribs and Main Fwd/Aft Center Wing Spars, Fuselage : Complete.
WIP: Wings
dhogue
 
Posts: 71
Joined: Mon Sep 15, 2014 8:39 pm
Top

Re: Ream Aileron Paddle flanged pivot bearing hole?

Postby Bryan Cotton » Thu Nov 13, 2014 8:33 pm

I have bought several reamers from Enco.
http://www.use-enco.com/CGI/INPDFF?PMPAGE=1126

It is always better to use a drill press if you can, unless you are a Terminator.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5496
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Ream Aileron Paddle flanged pivot bearing hole?

Postby GordonTurner » Thu Nov 13, 2014 9:23 pm

I guess I haven't got to that step yet...what the hell is a flanged bearing pivot?
Waiex 158 New York. N88YX registered.
3.0 Liter Corvair built, run, and installed.
Garmin panel, Shorai LiFePo batteries.
GordonTurner
 
Posts: 669
Joined: Tue Feb 21, 2012 1:14 am
Location: NY, NY
Top

Re: Ream Aileron Paddle flanged pivot bearing hole?

Postby dhogue » Thu Nov 13, 2014 10:14 pm

Thanks for the informative link Bryan.

Re:
GordonTurner wrote:I guess I haven't got to that step yet...what the hell is a flanged bearing pivot?

ONX-W21-04 Bellcrank Pivot.

;) Getting there: Page ONX-W21 (Detail of-03 Aileron Pivot Assembly)
Don Hogue
Onex 0173: Tailwheel: AeroVee Turbo.
Horiz/Vert Stabs, Rudder/Elevators, Fwd/IB/OB/Aileron Bellcranks on Ribs and Main Fwd/Aft Center Wing Spars, Fuselage : Complete.
WIP: Wings
dhogue
 
Posts: 71
Joined: Mon Sep 15, 2014 8:39 pm
Top

Re: Ream Aileron Paddle flanged pivot bearing hole?

Postby A10snoopy » Fri Nov 14, 2014 4:58 pm

Don, I did not ream, just pressed the bearings in place.

Paul, OneX 76
A10snoopy
 
Posts: 26
Joined: Fri Aug 19, 2011 9:19 am
Top

Post a reply

Return to Onex

Who is online

Users browsing this forum: No registered users and 2 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

SonexBuilders.net is NOT affiliated with Sonex Aircraft LLC. Discussion contents reflect the views of individual participants only. The owner of SonexBuilders.net makes no guarantees about the correctness or the accuracy of ANY of the information on or in any area or page of SonexBuilders.net. Verify ALL information obtained from SonexBuilders.net with the kit designer, equipment manufacturer, or other original official source before using that information. By participating in this website in any form, (including but not limited to reading, viewing, posting, and private messaging) you agree not to hold the owner (AVED LLC), owner members, forum members, or advertisers of SonexBuilders.net legally liable for information found on any of the pages of the website.

SonexBuilders.net is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.