SonexBuilders.net

A Forum for Sonex Aircraft Builders and Enthusiasts

Skip to content

LogoLogoLogo
random user submitted photo

Oil Cap Mod

Discussion of the Aerovee kit engine.
Post a reply

Oil Cap Mod

Postby GraemeSmith » Sat Feb 29, 2020 5:08 am

A little mod to the oil cap to make it easier to grip to open. Especially if reaching through a small oil door in the cowl. The "lacing eye" ring came from West Marine...

OilCap.jpg
Graeme JW Smith
User avatar
GraemeSmith
 
Posts: 939
Joined: Sat May 18, 2019 8:58 am
Location: RI
Top

Re: Oil Cap Mod

Postby Matt541 » Sat Feb 29, 2020 4:09 pm

I like it!

Just might have to steal that idea for 541...
Sonex 541, TD, Center Stick, Revmaster w/ Prince P <SOLD>
:arrow: Anxiously awaiting the new Highwing
User avatar
Matt541
 
Posts: 195
Joined: Mon Jan 13, 2020 3:29 pm
Location: Eastern PA
Top

Re: Oil Cap Mod

Postby rdsafe » Sun Mar 01, 2020 10:53 am

How about using an old style 1 1/2" key ring through a bolt/screw and nut of your choice. Works for me.
rdsafe
rdsafe
 
Posts: 27
Joined: Wed Mar 26, 2014 8:41 pm
Top

Re: Oil Cap Mod

Postby GraemeSmith » Sun Mar 01, 2020 5:46 pm

rdsafe wrote:How about using an old style 1 1/2" key ring through a bolt/screw and nut of your choice. Works for me.
rdsafe

I was trying to avoid any nut on the inside of the cap that might work loose and fall inside the case. The lacing eye is riveted to the edges of the cap outside the case.
Graeme JW Smith
User avatar
GraemeSmith
 
Posts: 939
Joined: Sat May 18, 2019 8:58 am
Location: RI
Top

Re: Oil Cap Mod

Postby rdsafe » Sun Mar 01, 2020 10:48 pm

GraemeSmith: The bolt/screw goes in from the bottom and the nut of your choice goes to the top side. Now you drill a hole through the bolt/screw and if you wish, the nut and install the key ring. Tell me ---- how is going to fall into the crankcase? Its not!
rdsafe
rdsafe
 
Posts: 27
Joined: Wed Mar 26, 2014 8:41 pm
Top

Re: Oil Cap Mod

Postby bvolcko38 » Mon Mar 02, 2020 10:29 am

I used an AN eyebolt and nylock and key ring
Bill Volcko XNS0068
Xenos A N68WV 99% flush rivets
Aerovee and Prince P-Tip
MGL Discovery Lite w/ Sandia STX 165R
V6
First hole 4/1/16
First flight 8/24/18
Phase I complete...finally!!!
Also flying a Challenger II since 1999
User avatar
bvolcko38
 
Posts: 284
Joined: Fri Feb 19, 2016 7:40 am
Location: Finger Lakes
Top

Post a reply

Return to Aerovee

Who is online

Users browsing this forum: No registered users and 56 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

SonexBuilders.net is NOT affiliated with Sonex Aircraft LLC. Discussion contents reflect the views of individual participants only. The owner of SonexBuilders.net makes no guarantees about the correctness or the accuracy of ANY of the information on or in any area or page of SonexBuilders.net. Verify ALL information obtained from SonexBuilders.net with the kit designer, equipment manufacturer, or other original official source before using that information. By participating in this website in any form, (including but not limited to reading, viewing, posting, and private messaging) you agree not to hold the owner (AVED LLC), owner members, forum members, or advertisers of SonexBuilders.net legally liable for information found on any of the pages of the website.

SonexBuilders.net is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.