On a quest for the elusive "Dry AeroVee"

Discussion of the Aerovee kit engine.

Re: On a quest for the elusive "Dry AeroVee"

Postby Onex107 » Sat Sep 03, 2022 9:26 am

Me too. Bolts bottomed out. Double gasket?
OneX 107
N2107X
Onex107
 
Posts: 504
Joined: Mon Mar 24, 2014 6:44 pm
Location: Peoria, IL

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Sat Sep 03, 2022 9:51 am

Thanks Dale! I'll cut a few threads off of my bolts. I just drilled them for safety wire last night.

A double gasket seems like trouble to me.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Mon Sep 05, 2022 10:34 pm

Airplane is back together and the test run was good. My valve cover bolts were not too long. I checked with no gasket or seal around the bolt.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Thu Sep 08, 2022 2:15 pm

Progress - I flew for one hour this morning. Lots of oil out the breather. The belly was a mess. No oil on the hangar floor. I'm assuming that for the breather mess I just need it to puke until it's at a happy level. For the rest of it, I don't think I've succeeded in the quest, but it's enough to not oil up the floor. First time ever that I could lay on the hangar floor under the cowl without cleaning it first.

As far as this breather thing goes - I wish I had one on all my old cars. They would never rust.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Fri Sep 09, 2022 10:35 am

I wonder what would happen if the breather was on the oil fill spot and visa versa. Then the cam gear would not sling oil at the breather.

Edit: or maybe the fuel pump blockoff for the breather.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: On a quest for the elusive "Dry AeroVee"

Postby Area 51% » Fri Sep 09, 2022 1:30 pm

Valve covers make a good location for vents. CB Performance sells the required fittings 2 for ten bucks.
Area 51%
 
Posts: 804
Joined: Thu Feb 18, 2016 7:57 am

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Fri Sep 09, 2022 2:35 pm

Area 51% wrote:Valve covers make a good location for vents. CB Performance sells the required fittings 2 for ten bucks.

Interesting - do you need two or just one?
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: On a quest for the elusive "Dry AeroVee"

Postby Area 51% » Fri Sep 09, 2022 7:04 pm

Two are always better.
Even if one was sufficient, my OCD about symmetry would dictate a matched pair.
Area 51%
 
Posts: 804
Joined: Thu Feb 18, 2016 7:57 am

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Fri Sep 09, 2022 7:34 pm

Area 51% wrote:Two are always better.
Even if one was sufficient, my OCD about symmetry would dictate a matched pair.


From what I've read since you put forth the idea, the 3/4 side fills with oil at higher RPMs and the 1/2 side doesn't. That's our left side, car right side. Any opinions on that?
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: On a quest for the elusive "Dry AeroVee"

Postby Bryan Cotton » Fri Sep 09, 2022 9:04 pm

Area 51% wrote:Valve covers make a good location for vents. CB Performance sells the required fittings 2 for ten bucks.

Correction - they sell 2 for $9.95. And, if your shopping cart is less than $10, they won't let you check out.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5475
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

PreviousNext

Return to Aerovee

Who is online

Users browsing this forum: No registered users and 5 guests