SonexBuilders.net

A Forum for Sonex Aircraft Builders and Enthusiasts

Skip to content

LogoLogoLogo
random user submitted photo

Cotton Waiex 191 - N191YX

Use this area to create a thread with photos from your build.
Post a reply

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Wed Sep 18, 2013 10:09 pm

I assembled the left hand side with similar results. This time I was careful to take the springback out of the flanges, so the bottoms were 90 and the tops matched the angle of the front spar in the plans. I did not think that would make a difference for a dry fit, as on the right side the clecoes were able to pull everything in without difficulty. I checked the straightness of the aft spar and the forward spar (with the hockey stick removed for convenience) and they were good. Any ideas? I have the question into Sonex tech support.
Attachments
image.jpg
Both stabs
image.jpg (83.81 KiB) Viewed 244222 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Fri Sep 20, 2013 9:45 am

Skins....
Attachments
image.jpg
image.jpg (104.67 KiB) Viewed 244183 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Sat Sep 21, 2013 5:32 pm

First rivets!
Attachments
image.jpg
image.jpg (91.38 KiB) Viewed 244170 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Sun Sep 22, 2013 6:44 pm

My forward spars for my stabilizers are riveted.
Attachments
image.jpg
Hockey stick riveted, rib clips bolted
image.jpg (62.47 KiB) Viewed 244139 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Fri Sep 27, 2013 8:54 am

Ok, I found that WIX-T11-09 rib was the culprit. It was too long, both parts. I am going to hack off the angled tab and rivet on another to make the proper spacing. Lesson learned: if things don't fit measure all the parts and compare to the plans.
Attachments
image.jpg
Only -09 is wrong
image.jpg (110.61 KiB) Viewed 244059 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Sat Oct 12, 2013 6:49 pm

We riveted together the right hand tail skeleton. I used AN426 4-4's as I had a regular #30 dimple die I was willing to grind down. These are Adam's first bucked rivets.
Attachments
image.jpg
image.jpg (87.69 KiB) Viewed 243961 times
image.jpg
Done!
image.jpg (96.09 KiB) Viewed 243961 times
image.jpg
Bucking rivets
image.jpg (108.62 KiB) Viewed 243961 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Wed Oct 23, 2013 11:36 pm

We finished riveting the skeletons together. I drilled on the hinges tonight. I made a little tool to help with the drilling - a piece of furring strip with a groove to clear the hinge.
Deleted photos for quota
Attachments
image.jpg
Holes drilled and clecoed
image.jpg (102.46 KiB) Viewed 243899 times
Last edited by Bryan Cotton on Wed Apr 09, 2014 10:03 pm, edited 1 time in total.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Thu Oct 24, 2013 11:14 pm

Skins clecoed. Need to bring the bottoms all up to #30, Adam and I did the tops earlier.
Attachments
image.jpg
image.jpg (106.16 KiB) Viewed 243864 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Sat Oct 26, 2013 5:26 pm

The joy of deburring- it is better when shared.
Attachments
image.jpg
image.jpg (98.33 KiB) Viewed 243837 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: Cotton Waiex 191 - N191YX

Postby Bryan Cotton » Sun Oct 27, 2013 6:06 pm

We are mostly deburred. Tried polishing for the first time.
Attachments
image.jpg
12 year old automatic polishing machine
image.jpg (69.04 KiB) Viewed 243813 times
image.jpg
Hey... it works
image.jpg (73.85 KiB) Viewed 243813 times
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5489
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

PreviousNext
Post a reply

Return to Photo Album

Who is online

Users browsing this forum: No registered users and 2 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

SonexBuilders.net is NOT affiliated with Sonex Aircraft LLC. Discussion contents reflect the views of individual participants only. The owner of SonexBuilders.net makes no guarantees about the correctness or the accuracy of ANY of the information on or in any area or page of SonexBuilders.net. Verify ALL information obtained from SonexBuilders.net with the kit designer, equipment manufacturer, or other original official source before using that information. By participating in this website in any form, (including but not limited to reading, viewing, posting, and private messaging) you agree not to hold the owner (AVED LLC), owner members, forum members, or advertisers of SonexBuilders.net legally liable for information found on any of the pages of the website.

SonexBuilders.net is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.