SonexBuilders.net

A Forum for Sonex Aircraft Builders and Enthusiasts

Skip to content

LogoLogoLogo
random user submitted photo

SNX-C02

Discussion for Sonex builders on specific plans page experience. These posts are limited to technical suggestions such as assembly order, challenges, or techniques related to specific plans pages.
Post a reply

SNX-C02

Postby Bryan Cotton » Wed Jun 01, 2016 2:05 pm

I think that is the right page reference. Anyway, the four 5/8" ID 3/4" OD bronze bushings are supposed to press into the weldment that holds the sticks. Mine drop in. How can I line bore them if they spin in the tube? Should I bond them in? Duct tape?
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 5035
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77
Top

Re: SNX-C02

Postby GordonTurner » Wed Jun 01, 2016 6:20 pm

Bryan,

It's no 150....you're supposed to use gorilla tape.

Gordon
Waiex 158 New York. N88YX registered.
3.0 Liter Corvair built, run, and installed.
Garmin panel, Shorai LiFePo batteries.
GordonTurner
 
Posts: 646
Joined: Tue Feb 21, 2012 1:14 am
Location: NY, NY
Top

Re: SNX-C02

Postby MichaelFarley56 » Wed Jun 01, 2016 6:54 pm

It's been a few years Bryan but I'm fairly certain I just glued mine in place with epoxy. They've never moved since I installed them!
Mike Farley
Waiex #0056 - N569KM
Jabiru 3300A #1706
MGL Panel
MichaelFarley56
 
Posts: 1473
Joined: Thu Jun 02, 2011 11:38 pm
Location: Columbus, Ohio
Top

Re: SNX-C02

Postby rizzz » Wed Jun 01, 2016 11:03 pm

Looking back at my log, it appears I had the same problem, used JB Weld:
http://www.mykitlog.com/users/display_l ... 286&row=74
Michael
Sonex #145 from scratch (mostly)
Taildragger, 2.4L VW engine, AeroInjector, Prince 54x48 P-Tip
VH-MND, CofA issued 2nd of November 2015
First flight 7th of November 2015
Phase I Completed, 11th of February 2016
http://www.mykitlog.com/rizzz/
rizzz
 
Posts: 869
Joined: Tue Jun 21, 2011 2:07 am
Location: Wollongong, NSW, Australia
Top

Post a reply

Return to Sonex Plans

Who is online

Users browsing this forum: No registered users and 10 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

SonexBuilders.net is NOT affiliated with Sonex Aircraft LLC. Discussion contents reflect the views of individual participants only. The owner of SonexBuilders.net makes no guarantees about the correctness or the accuracy of ANY of the information on or in any area or page of SonexBuilders.net. Verify ALL information obtained from SonexBuilders.net with the kit designer, equipment manufacturer, or other original official source before using that information. By participating in this website in any form, (including but not limited to reading, viewing, posting, and private messaging) you agree not to hold the owner (AVED LLC), owner members, forum members, or advertisers of SonexBuilders.net legally liable for information found on any of the pages of the website.

SonexBuilders.net is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.