Canopy install

Discussion for Sonex builders on specific plans page experience. These posts are limited to technical suggestions such as assembly order, challenges, or techniques related to specific plans pages.

Canopy install

Postby Gripdana » Sat Aug 30, 2014 9:16 pm

I just got my canopy and am getting ready to trim and fit it. I know it goes on perpendicular to it's form but is there a front and back? Is the front where Sonex has put the sticker?
Dana Baker
Scratch Built
First Flight March 8, 2015
Sonex #1534 - N1534S "Aluminum Foil"
Aerovee-Dual Controls-Tail Dragger
Gripdana
 
Posts: 479
Joined: Fri Jan 11, 2013 5:59 pm

Re: Canopy install

Postby MichaelFarley56 » Sat Aug 30, 2014 9:41 pm

Is there no marking or label indicating the front of the canopy Dana? Did they write anything on the masking tape outline?

I'm fairly certain the front is where the label is, but it's been a while since I fit mine. Hopefully someone else can provide confirmation!
Mike Farley
Waiex #0056 - N569KM
Jabiru 3300A #1706
MGL Panel
MichaelFarley56
 
Posts: 1470
Joined: Thu Jun 02, 2011 11:38 pm
Location: Columbus, Ohio

Re: Canopy install

Postby Gripdana » Sat Aug 30, 2014 11:12 pm

Well I should have unpacked it. I was looking at it in the box and the edges were pressed against the sides of the box. I saw the markings after I unpacked it. Wow do I feel stupid. Thanks.
Dana Baker
Scratch Built
First Flight March 8, 2015
Sonex #1534 - N1534S "Aluminum Foil"
Aerovee-Dual Controls-Tail Dragger
Gripdana
 
Posts: 479
Joined: Fri Jan 11, 2013 5:59 pm

Re: Canopy install

Postby Gripdana » Mon Sep 01, 2014 6:36 pm

I found the front and today my brother came over to help cut the canopy. I followed the Sonex video instructions exactly. Everything went very well so far. The canopy is cut down to close forward and aft (needs sanding to final size). The sides are close and will be final trimmed as I get the fore and aft finished.
Attachments
IMG_4774.jpg
IMG_4774.jpg (36.49 KiB) Viewed 6928 times
IMG_4771.jpg
IMG_4771.jpg (46.14 KiB) Viewed 6928 times
IMG_4770.jpg
IMG_4770.jpg (63.25 KiB) Viewed 6928 times
Dana Baker
Scratch Built
First Flight March 8, 2015
Sonex #1534 - N1534S "Aluminum Foil"
Aerovee-Dual Controls-Tail Dragger
Gripdana
 
Posts: 479
Joined: Fri Jan 11, 2013 5:59 pm

Re: Canopy install

Postby mike.smith » Tue Sep 02, 2014 7:37 pm

Now that I've been through a summer with my canopy I'll throw this out there.

The canopy will expand and contract a lot with temperature. DO make sure you oversize the holes for the screws. DO make sure you leave a sufficient gap between the back edge of the canopy and the turtledeck, and between the front edge of the canopy and the windscreen.

My inclination was to make the gaps as small as I could. But in the first summer sunshine it began pressing against the turtledeck and the windscreen, and I had to do some sanding to make the gaps larger.

Don't force anything. I had a perfect canopy going until I tried to force a rivet into a hole that should have been drilled out just a tad more. Then "crack!" I stop drilled the hole, but it is forever a reminder that if I had been just a LITTLE more patient I would have been totally crack free.

Mike Smith
Sonex N439M
Mike Smith
Sonex N439M
Scratch built, AeroVee, Dual stick, Tail dragger
http://www.mykitlog.com/mikesmith
mike.smith
 
Posts: 1406
Joined: Tue Jan 29, 2013 8:45 pm

Re: Canopy install

Postby Darick » Tue Sep 02, 2014 7:44 pm

What do you consider a sufficient gap...1/16, 1/8, 3/16....?
Darick Gundy
Sonex #1646
N417DG
Taildragger, Aerovee, center stick, Prince P-Tip Prop
MGL E1, F2, V6 radio, Sandia Xponder, Reserve lift indicator (AOA), iFly 520
First flight! 10/21/2017
User avatar
Darick
 
Posts: 496
Joined: Mon Aug 05, 2013 9:39 pm
Location: PA

Re: Canopy install

Postby Gripdana » Tue Sep 02, 2014 10:50 pm

Thanks for the advise Mike. So far I am keeping around a 1/16" gap forward and aft per the plans. I think the gap will change when I frame it up. I cut the canopy in the sun and it was 100 degrees out. That helped with the cutting. Today was spent trimming and finessing the fit. Next I will assemble the frame and attach the canopy.
Dana Baker
Scratch Built
First Flight March 8, 2015
Sonex #1534 - N1534S "Aluminum Foil"
Aerovee-Dual Controls-Tail Dragger
Gripdana
 
Posts: 479
Joined: Fri Jan 11, 2013 5:59 pm

Re: Canopy install

Postby mike.smith » Thu Sep 04, 2014 12:11 am

Darick wrote:What do you consider a sufficient gap...1/16, 1/8, 3/16....?


I think the 1/16" on the plans is a good start, but just wouldn't go smaller. I tried to go smaller, figuring I was going to make a nice airtight canopy (OK, not really airtight, but I couldn't think of another description). I ended up trimming.

Mike Smith
Mike Smith
Sonex N439M
Scratch built, AeroVee, Dual stick, Tail dragger
http://www.mykitlog.com/mikesmith
mike.smith
 
Posts: 1406
Joined: Tue Jan 29, 2013 8:45 pm

Re: Canopy install

Postby Sonex555 » Thu Sep 04, 2014 8:21 am

Word of Caution: the canopy will expand in the sun. I know a gentleman that spent a month getting a perfect tight fit only to close the canopy in the afternoon sun and came back to find a huge crack in the canopy.

John Davis
Sonex555
 
Posts: 7
Joined: Fri Jun 03, 2011 8:18 am

Postby Fastcapy » Thu Sep 04, 2014 1:30 pm

-----
Last edited by Fastcapy on Tue Feb 24, 2015 2:54 pm, edited 1 time in total.
Mike Beck
Oshkosh, WI (KOSH)
Sonex #1145 N920MB
Std Gear, Modified Aerovee, Rotec TBI, Dual Stick, Acro Ailerons
MGL Panel
Airworthiness: 10/24/13, First Flight: 05/18/14
Fastcapy
 
Posts: 335
Joined: Sun Jan 12, 2014 11:45 am
Location: KOSH

Next

Return to Sonex Plans

Who is online

Users browsing this forum: No registered users and 1 guest