Page 8 of 15
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Fri May 20, 2016 12:25 amby kevinh
Bryan Cotton wrote:I have done one 1/8" fitting by each method. The step drill one came out better. Ironically I still spun the fitting on that one. My steam punk drill takes about a minute to coast down so that sucked. I used the dremel with a high speed cutter and I finished up with the holesaw.
Hi Bryan,
Can you elaborate on this? How did you use the dremel to recover after the fitting spun? (Asking because I'm doing mine next week and want to have the tricks ready) :twisted:
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Fri May 20, 2016 7:21 amby Bryan Cotton
Kevin,
By high speed cutter I mean this:
https://www.cessna120-140.org/forum/dow ... hp?id=3635I don't exactly remember but I think I used the cutter to hog out the aluminum. Then I finished the hole. Not sure how I guided the holesaw after, maybe I used the force.
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Sat May 28, 2016 1:30 pmby Darick
Kevin, borrow the tool from (jeez, I can't remember) to sand off the inside of the hole, to make it flat for the oops fitting to seal against. Somebody will remember who loans out the tool. It made the job much easier for me.
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Sat May 28, 2016 1:38 pmby WaiexN143NM
Hi darick, and kevin, and all,
I think you guys are refering to mr david amsler ''DCASonex'
A few friends have borrowed his tools and advice.
WaiexN143NM
Michael
Sonex Fuel Tank & Oops Fittings
Posted:
Sat May 28, 2016 4:48 pmby Sonex1517
That is correct. I think David now has the tool back after I had it and sent it to the next builder that needed it.
That thing sure works!
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Sat May 28, 2016 6:15 pmby kevinh
oh yes - Dave already reached out to me, loaned me the _awesome_ tool and I did my tank. Now I just need to finish the fuse ;-)
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Tue Oct 04, 2016 8:50 pmby thomasjones42
Are DCA's tools for fitting the OOPs fittings still available for loan?
Tom Jones
Onex 0133
Aerovee turbo
Sonex Fuel Tank & Oops Fittings
Posted:
Tue Oct 04, 2016 10:01 pmby Sonex1517
thomasjones42 wrote:Are DCA's tools for fitting the OOPs fittings still available for loan?
Tom Jones
Onex 0133
Aerovee turbo
They are out there in Sonex land somewhere.....I believe I either returned them or passed them along....
Robbie
Sent from my iPad using Tapatalk
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Wed Oct 05, 2016 8:53 amby DCASonex
thomasjones42 wrote:Are DCA's tools for fitting the OOPs fittings still available for loan?
Tom Jones
Onex 0133
Aerovee turbo
Tom, They are back in my tool box having done more traveling since Robbie had them. PM me with your shipping address and reimburse the $7 Priority Mail cost when you return them.
David A.
Re: Sonex Fuel Tank & Oops Fittings
Posted:
Wed Oct 05, 2016 10:47 pmby thomasjones42
DCASonex wrote:thomasjones42 wrote:Are DCA's tools for fitting the OOPs fittings still available for loan?
Tom Jones
Onex 0133
Aerovee turbo
Tom, They are back in my tool box having done more traveling since Robbie had them. PM me with your shipping address and reimburse the $7 Priority Mail cost when you return them.
David A.
Not certain how to use PM feature
1075 Merry Lane
Van Wert, Ohio 45891