Wing ribs too wide

Use this area for aviation related general discussions, newsworthy items, and non model specific topics.

Wing ribs too wide

Postby Sonex1542 » Sun Jun 07, 2015 5:52 pm

Seems like my ribs are a bit too wide for the main spar. About .020-.040. Some of this I can probably take up with just a bit of extra bending in rolling over the flange, but not the entire amount in some.

Would it be acceptable to add a shim between the spar and skin? Or just rework the ribs?
SNX-794. Formerly SNX-1542
Sonex1542
 
Posts: 53
Joined: Wed Sep 21, 2011 12:09 am
Location: Reno, NV

Re: Wing ribs too wide

Postby Bryan Cotton » Sun Jun 07, 2015 6:47 pm

I would definitely check in with Sonex. I don't believe there would be an issue with a shim. I put shims on my outboard wing ribs of my hummelbird. That was a scratch build. I had made my oak spar tooling perfect. Soon as I made it I did the center spar, but then did the outer spars a year or more later and the oak tooling changed dimension slightly. That wood is untrustworthy stuff, that is why we build metal airplanes.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 4953
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: Wing ribs too wide

Postby SNX1508 » Sun Jun 07, 2015 7:31 pm

Sonex1542 wrote:Seems like my ribs are a bit too wide for the main spar. About .020-.040. Some of this I can probably take up with just a bit of extra bending in rolling over the flange, but not the entire amount in some.

Would it be acceptable to add a shim between the spar and skin? Or just rework the ribs?


Too wide or do you mean too high? If the rib is only too high where the rib meets the main spar, I read somewhere, either on this forum of in the Sonex plans, about modifying the top / forward edge of the rib so that you can bend it down slightly so the skin does not end up with a very small dimple in it at each rib.

Terry
Terry
Sonex #1508
N296SX
AeroVee #0736
Tail Dragger
http://www.mykitlog.com/SNX1508
SNX1508
 
Posts: 69
Joined: Sun Dec 11, 2011 6:53 am

Re: Wing ribs too wide

Postby sonex892 » Sun Jun 07, 2015 8:40 pm

Front rib, rear rib or both? Remember the front skin is actually shimmed by the rear skin. If a shim is actually needed I agree with Bryan and doubt it will be an issue. Most Sonerai's with store bought spars need to be shimmed to avoid a dip in the skin at the spar.

Steve
Sonex 892
sonex892
 
Posts: 169
Joined: Fri Jun 03, 2011 4:49 am
Location: Port Macquarie Australia

Re: Wing ribs too wide

Postby Sonex1542 » Mon Jun 08, 2015 11:09 am

Primarily it was the rear rib that is slightly wider. I also thought about the possibility of the rear acting as a shim for the front, but its kinda reverse in this situation. Maybe do a deeper dive on the web for shimming the main spar. I haven't read about shimming other than the formers on the turtle deck. Moreso, I wanted to avoid the ribs entirely and found what turned out to be a 90% kit. With the wings looking 90% complete. Everything seems to be to plans, but this wasnt expected.

Thanks. Trying to wrap up the wings this year and be in the air by spring 16'
SNX-794. Formerly SNX-1542
Sonex1542
 
Posts: 53
Joined: Wed Sep 21, 2011 12:09 am
Location: Reno, NV

Re: Wing ribs too wide

Postby Bryan Cotton » Mon Jun 08, 2015 11:40 am

I would think that if the skins step down to the spar from the aft ribs, and the LE skin fills that step, that is perfect. I have not built my wings yet.
Bryan Cotton
Poplar Grove, IL C77
Waiex 191 N191YX
Taildragger, Aerovee, acro ailerons
dual sticks with sport trainer controls
Prebuilt spars and machined angle kit
Year 2 flying and approaching 200 hours December 23
User avatar
Bryan Cotton
 
Posts: 4953
Joined: Mon Jul 01, 2013 9:54 pm
Location: C77

Re: Wing ribs too wide

Postby Gripdana » Mon Jun 08, 2015 12:10 pm

If I remember correctly my ribs did not exactly match the width of the spar. I scratch built #1534. I laid a sample from scrap over the spar and ribs as it will be with the skins installed to confirm the alignment. Are you scratch building or building from a kit? I may have tweeted the ribs a bit to get them just right. It has been 3 years since I made the wings. Here is a link to my builders website and Flicker. There are a lot of photos.
http://websites.expercraft.com/gripdana/
https://www.flickr.com/cameraroll
Dana Baker
Scratch Built
First Flight March 8, 2015
Sonex #1534 - N1534S "Aluminum Foil"
Aerovee-Dual Controls-Tail Dragger
Gripdana
 
Posts: 479
Joined: Fri Jan 11, 2013 5:59 pm

Re: Wing ribs too wide

Postby Gripdana » Mon Jun 08, 2015 12:11 pm

I hate auto correct. I may have "tweaked" the ribs.
Dana Baker
Scratch Built
First Flight March 8, 2015
Sonex #1534 - N1534S "Aluminum Foil"
Aerovee-Dual Controls-Tail Dragger
Gripdana
 
Posts: 479
Joined: Fri Jan 11, 2013 5:59 pm

Re: Wing ribs too wide

Postby Rynoth » Mon Jun 08, 2015 2:39 pm

The rear ribs will be higher/wider than the aft side of the main spar, since the aft wing skins attach at the forward part of the main spar. I.e. the wing skins don't necessarily contact the aft edge of the spar due to how they're folded over the spar. I'm not saying you don't need to modify your ribs, just be sure you're not trying to fix a problem that doesn't actually exist.
Ryan Roth
N197RR - Waiex #197 (Turbo Aerovee Taildragger)
Knoxville, TN (Hangar at KRKW)
My project blog: http://www.rynoth.com/wordpress/waiex/
Time-lapse video of my build: https://www.youtube.com/watch?v=Q8QTd2HoyAM
User avatar
Rynoth
 
Posts: 1308
Joined: Fri Jul 26, 2013 1:32 pm
Location: Knoxville, TN

Re: Wing ribs too wide

Postby dbdevkc » Wed Oct 11, 2017 10:41 pm

I am curious if anyone else has experienced this and what they did about it.
[color=#800000]Kevin Conklin
Building Waiex #169
dbdevkc
 
Posts: 193
Joined: Sun Jun 26, 2011 9:18 am
Location: Washingtonville, NY

Next

Return to General Discussion

Who is online

Users browsing this forum: No registered users and 23 guests